6
MECHANICAL NEUTRAL SAFETY SWITCH (Rear Wheel Drive Only)
When installing a Bulldog remote starter on GM vehicles or Dodge Dakotas built prior to 1996, you
must: Use the diagram below to create a circuit that will prevent the remote starter from starting
the vehicle unless the key is removed from the ignition switch.
PRE-1996 GM REAR WHEEL DRIVES WITH PURPLE CRANK WIRE – Optional part #775 required.
86
30
87a
87
85
5 Amp
fuse
Tie into
heavy white
wire on
4-relay
harness
(-) Negative
hood pin wire
Message
center or
key buzzer
Driver’s Door Switch
Key
Cylinder
TAN
GREEN
BLACK
YELLOW
BLUE
WHITE
NOT USED,
TAPE OFF
RED
Ground
Ground
86
30
87a
87
85
5 Amp
fuse
Tie into
heavy white
wire on
4-relay
harness
(-) Negative
hood pin wire
Message
center or
key buzzer
Driver’s Door Switch
Key
Cylinder
BLACK/LT.BLUE
LT.BLUE/GREEN
BLACK
YELLOW
BLUE
WHITE
RED
PRE-1996 DODGE DAKOTAS
Optional part #775 required.
NOT USED,
TAPE OFF
Ground
Ground
NEUTRAL SAFETY SWITCH
CONNECTING THE 12-PIN HARNESS & 4-RELAY HARNESS
AUXILIARY INPUT
If you wish to use this starter with an aftermarket alarm, connect the BLUE wire from the 12-pin
harness to the second or third channel (-) output of your existing alarm. When the output is
activated, a (-) signal will be supplied to the remote starter.
CAUTION: Before connecting the 12-pin harness
to the module, double check all connections
to be sure they are secure and properly wrapped
with electrical tape. Mount the unit under
the driver’s side dash. Make sure to properly
place antenna. (See antenna placement page
7.) Plug the 12-pin harness into the main
control module. Once it is plugged in, press
and release transmitter button #4, the parking
lights flash 3 times. The flash confirms that
the transmitter code has been programmed to
the unit. Once the module is programmed,
connect the 3-pin harness from the 4-relay
harness to the module. NOTE: There are (2)
wires in the 12-pin harness that will not be
used. All unused wires must be taped.
Press the start button, the parking lights
will flash once and the vehicle will start
and run. NOTE: If your vehicle does not start
and run you may have a factory anti-theft
system. Refer to page 7 to see if this applies
to your vehicle.
GREEN/BLACK
BLUE/WHITE
BLUE
VIOLET
WHITE/RED
WHITE/ORANGE
ORANGE
BROWN
GRAY
YELLOW
BLACK
RED
(-) Tach Input
(-) To hood pin switch
(-) Aux. alarm channel input
(not used)
(-) Factory Alarm Shutdown
(not used)
(+) Brake Input
(+) Parking lights
(-) Negative Horn Output
Ignition input
Ground
To +12V constant
WHT/BLK 16 ga.
WHITE 16 ga.
YEL/BLK 16 ga.
RED
2 Red wires need
+12V constant.
Either white wire
to Ignition 1. If
your car has 2
ignitions use both.
To Starter/Crank
Wire
To Accessory
Wire(s) that run
the Heater/Blower
Motor. Attach at
the ignition switch
wire harness only.
RED
WHITE
WHITE
YELLOW/BLACK
WHITE/BLACK
YELLOW
ANTENNA
Keep as
straight as
possible,
tape end
to hold
straight.
Tap here when
installing bypass
module 721.
WHITE 16 ga
WHT/BLK 16 ga
YEL/BLK 16 ga
For Passlock I
For Passlock I
For Passlock II
750ma (-)
Outputs
(12 strony)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji